VLM CCT 400-FL WA I +60°C Cyclic Corrosion Testing Chamber
Advanced Compact steel designed front-loading cabinet for corrosion testing
Operating temperature from ambient up to +60°C
User friendly, VLM intuitive control system with colour display and preconfigured corrosion tests installed
VLM CCT 400-FL WA I +60°C Cyclic Corrosion Testing Chamber
Operating temperature from ambient up to +60°C
Compact front-loading cabinet for corrosion testing developed for conducting advanced automatic cyclic corrosion tests pursuant to major corporate standards in the international automotive industry such as:
- DIN EN ISO 11997-1:2006 Cycle B (previously VDA 621-415)
- VW PV 1210 (external climate module required)
- GMW 14872 (external climate module required)
This test cabinet is also suitable for performing standard corrosion tests:
- Water condensation DIN EN ISO 6270-2:2005 (CH, AT, AHT), ASTM D2247
- Salt spray ISO 9227, IEC 60028-2-11 KA
Customer Benefits
- The advanced steel design of the chamber allows for fast temperature and humidity transient times making this test chamber perfectly suitable for accelerated corrosion tests – these result in time and energy savings during the operational lifetime
- The patented VLM technology allows the best possible reproducibility of the climate conditions being created in the test chamber regardless of the environmental conditions and geographical location
- The test chamber made of steel is more robust and less susceptible to damage compared to the competitive products made of glass-reinforced plastic.
- Lower cost of ownership compared to the competitive products where the test chamber is made of glass-reinforced plastic (shorter test periods, better energy efficiency, easier for service and maintenance, longer life cycle, more resistive to mechanical damages)
- User friendly, menu guided and intuitive control system based on a versatile controller with colour display in which most common standard corrosion tests are already preconfigured
The following Accessories are included:
6 rods for supporting test specimen
2 m exhaust hose Ø 50 mm
2 m drain water hose Ø 18 mm
1 female connector for compressed air hose (size no. 5)
1 bag sodium chloride special quality for corrosion testing, accurate weight 5000 g
1 set of measuring cylinders for measuring the fall our rate
1 spare filter for the test solution in the reservoir
-
Relevant Test Standards
Cyclic Corrosion Tests:
- DIN EN ISO 11997-1:2006 Cycle B (previously VDA 621-415)
- VW PV 1210 (climate module required)Salt Spray Test:
- DIN EN ISO 9227
- DIN 50942, DIN 53167
- ASTM B 117-73, ASTM B 287-74
- ASTM B 368-68
- ISO 7253 ISO 3678
- BS 1224, BS 2011, BS3900 F4
- BS 3900 F12
- BS 5466 Part I, BS 5466 Parts 2 + 3
- NFX 41002,
- AS 21331 Section 3.1
- SIS 1841190
- JIS Z 2371
- IEC 60028-2-11 KACondensation water test:
- ISO 6270-2
- BS 3900F2, BS 3900 F15
- ASTM D2242Technical Specifications
Capacity ca. 400 L Inner test chamber dimensions W/D/H1/H2 ca. 800 x 605 x 733/920 mm Outer dimensions of the casing (overall) W/D/H ca. 1310 x 670 x 1933 mm Max. operating temperature 60°C Required power supply 230 V, 50/60 Hz, 2200 W Materials used Test chamber is made of stainless steel and coated with ECTFE (Halar®), additional side walls made of special Polyethylene with milled openings for supporting rods Heating Flat Micanite heaters under the bottom of the chamber and behind the sidewalls for fast and uniform heat transfer Sensors Corrosion-resistant and highly sensitive temperature sensors above the floor and under the roof Cooling N/A Regulated humidity N/A Other Specification
Purity demineralized water (connection type) < 5 μS/cm (¾“ outer diameter) Tap water (connection type) Always via Ion-exchanging cartridge (¾“ outer diameter) Compressed Air 6-8 bar (connection nipple size 5) Wastewater, drain Pipe fittings (spiral hose ID 18 mm) Exhaust pipe outer diameter Pipe fitting (50 mm external diameter) Test solution tank capacity A 210 L tank is available which fits in the bench cabinet underneath the test chamber Recommended accessories Demineralized water plant, filter for compressed air, pump for mixing test solution, racks for specimen
-
Process Control
User friendly, menu guided JUMO Imago controller with colour graphic display
Restricted access for operators to three different operating levels
Memory storage with the capacity to hold up to 50 test programs with the most common corrosion tests already preconfigured in the factory
The controller steers the external climate module for the tests which require air conditioning (typically PV 1210)
A full overview of all digital and analogue inputs/outputsOperating System Salt Spray (according to ISO 9227)
Electronically controlled diaphragm pump for accurate flow control of the test solution with automatic monitoring of the presence of the air in the pump system
Adjustable high-performance acrylic spray nozzle for an optimal generation and distribution of the salt fog
Transparent humidifier made of heat resistant Borosilicate glass with a replaceable PE air filter
Safety air pressure valve on the humidifier
Over-temperature protection of the humidifier
Air purge function for rapid evacuation of the salt fog out of the chamber
Accessories: 210 L PE storage reservoir for test solution (level indicator optional)
Option: Aeration with warm air (WA)
Option: Nozzle for washing the test chamber after the salt spray test is finishedOperating system High Humidity with Controlled Water Condensation - CWC (according to ISO 6270-2 CH)
CWC system is the patented VLM technology which regulates the temperature gradient of exactly ΔT=1°C between the bottom and the roof of the test chamber – this is essential for an optimal condensation process in the test chamber at 100% RH regardless of the environmental conditions outside the test chamber
Flat heaters under the bottom of the chamber and behind sidewalls allow for uniform and rapid heating of the water in the trough
Temperature stability in the chamber ±0,5°C
Air fan with adjustableOperating system Forced Air Drying / Aeration
Aeration with environmental air (aeration with warm air is optional) during the forced air drying phase
Adjustable air distribution system inside the test chamber for uniform drying of the test specimens
Fan with controllable rotation speed
Option: Air conditioning module for providing standard climate acc. to DIN 50014: ambient air at 23°C ±2°C and 50% ±5% RH